How to remove Hot water Tank ?
In accordance with this 2010 California construction code, professionals and homeowners are needed to acquire a license to"install, remove, or substitute" water heater. These anchors, typically fastened to wall studs behind the water tank, maintain the tank protected in the event of a earthquake. The straps have to be emptied and the gas line and water shut off until the tank could be taken off. The job is rather straightforward and is readily accomplished with the correct tools.
1.Get a construction license from the local construction codes section. Get ready to pay a little charge and schedule a review from the codes officer after the container was taken away. If you're installing a replacement tank, then schedule the review when you've set up the new one.
2.Switch off the circuit breaker in the event the water tank is electrical. Proceed to the main service panel and then find the circuit to your water tank. To switch off the circuit breaker, then flip the little switch into the"off" place on the board. Proceed to the water tank and then unscrew the little hatch which covers the tank electrical wires, typically situated on peak of the tank. Carefully pry the wiring from the driveway. Evaluation for electric power by putting one end of this voltmeter wand onto the aluminum section of this white electrical wire and the opposite end of the voltmeter wand onto the aluminum of the black cable. The voltmeter shouldn't create a reading. Should it, switch off the main circuit breaker on the support panel. Press the primary switch down to the"off" place. When you're sure there's not any power running to the tank, then disengage the electric distribution wires from the tank circuit cables. Tuck the tank cables back down to the hatch in order that they stand out of the way as you work.
3.Switch off the gas supply in the event the tank is gas-fueled. The gasoline supply shut off valve is generally located several feet in the petrol pipe leading from the tank. Turn the gas supply shutoff valve handle in order it is vertical to the gas distribution pipe.
4.Switch off the water source to the tank. Start looking for the chilly water shutoff valve combined the water supply pipe close to the tank.
5.Twist on the family faucets to help drain some of their warm water out of the tank. Put the other end of the hose at a skillet nicely or outside. The water will probably be scalding hot, so put the hose in which the tank water may drain freely without damaging anybody or any thing. Switch the drain valve spigot open all of the way and permit the water to drain out of the tank.
6.Disconnect the pressure and temperature valve pipe in the face of the tank.
7. Put one adjustable wrench at the base of this marriage joint, a huge nut that joins two segments of pipe. Put the plumber's basin wrench onto the top half of their marriage joint. Flip the adjustable wrench at a clockwise direction and the basin wrench at a standardised way to loosen the marriage joint. After loose, then disengage the wrenches and unscrew the marriage combined by hand. Use the adjustable wrench to loosen and eliminate the little gas pipe section that's connected to the tank.
8.Disconnect both water supply pipes situated on peak of the tank. Some pipes can easily be unscrewed by hand, while some might require a twist having an adjustable wrench to loosen the nuts. In case the water distribution lines are copper pipes affixed into the tank, then you'll have to decrease the pipes in the tank using a pipe tube cutter. Put the cutter blade on the pipe and twist the blade by turning the little screw on the cutter's handle. Repeat to another distribution pipe.
9.Lift the flue pipe near the peak of the water heater to detach it in the little exhaust flange.
10.Eliminate the anchor straps or metallic plumber's tape strips out of the wall round the water heater. Use the ratchet screwdriver and set to remove the screws and nuts.
11.Have your helper grasp the tank and stop it from toppling over. Hint the tank ahead gradually to remove the tank out of its location and put the tank on its side. With your helper at the same end of the tank along with you in the flip side, lift the tank from every side and take it from this space.
Things You'll Need
· Voltmeter
· Screwdriver
· Assistant
· Ratchet Collection
· Warnings
Your primary service panel needs to be clearly marked to indicate that the hot water tank circuit breaker. When it isn't, consult with a professional electrician to ascertain the circuitry of your electric wiring.
If you disconnect the gas supply line in the water tank, then a small number of residual gas will ooze in the pipe. Don't ignite any fires when functioning on gasoline lines.
1.Get a construction license from the local construction codes section. Get ready to pay a little charge and schedule a review from the codes officer after the container was taken away. If you're installing a replacement tank, then schedule the review when you've set up the new one.
2.Switch off the circuit breaker in the event the water tank is electrical. Proceed to the main service panel and then find the circuit to your water tank. To switch off the circuit breaker, then flip the little switch into the"off" place on the board. Proceed to the water tank and then unscrew the little hatch which covers the tank electrical wires, typically situated on peak of the tank. Carefully pry the wiring from the driveway. Evaluation for electric power by putting one end of this voltmeter wand onto the aluminum section of this white electrical wire and the opposite end of the voltmeter wand onto the aluminum of the black cable. The voltmeter shouldn't create a reading. Should it, switch off the main circuit breaker on the support panel. Press the primary switch down to the"off" place. When you're sure there's not any power running to the tank, then disengage the electric distribution wires from the tank circuit cables. Tuck the tank cables back down to the hatch in order that they stand out of the way as you work.
3.Switch off the gas supply in the event the tank is gas-fueled. The gasoline supply shut off valve is generally located several feet in the petrol pipe leading from the tank. Turn the gas supply shutoff valve handle in order it is vertical to the gas distribution pipe.
4.Switch off the water source to the tank. Start looking for the chilly water shutoff valve combined the water supply pipe close to the tank.
5.Twist on the family faucets to help drain some of their warm water out of the tank. Put the other end of the hose at a skillet nicely or outside. The water will probably be scalding hot, so put the hose in which the tank water may drain freely without damaging anybody or any thing. Switch the drain valve spigot open all of the way and permit the water to drain out of the tank.
6.Disconnect the pressure and temperature valve pipe in the face of the tank.
7. Put one adjustable wrench at the base of this marriage joint, a huge nut that joins two segments of pipe. Put the plumber's basin wrench onto the top half of their marriage joint. Flip the adjustable wrench at a clockwise direction and the basin wrench at a standardised way to loosen the marriage joint. After loose, then disengage the wrenches and unscrew the marriage combined by hand. Use the adjustable wrench to loosen and eliminate the little gas pipe section that's connected to the tank.
8.Disconnect both water supply pipes situated on peak of the tank. Some pipes can easily be unscrewed by hand, while some might require a twist having an adjustable wrench to loosen the nuts. In case the water distribution lines are copper pipes affixed into the tank, then you'll have to decrease the pipes in the tank using a pipe tube cutter. Put the cutter blade on the pipe and twist the blade by turning the little screw on the cutter's handle. Repeat to another distribution pipe.
9.Lift the flue pipe near the peak of the water heater to detach it in the little exhaust flange.
10.Eliminate the anchor straps or metallic plumber's tape strips out of the wall round the water heater. Use the ratchet screwdriver and set to remove the screws and nuts.
11.Have your helper grasp the tank and stop it from toppling over. Hint the tank ahead gradually to remove the tank out of its location and put the tank on its side. With your helper at the same end of the tank along with you in the flip side, lift the tank from every side and take it from this space.
Things You'll Need
· Voltmeter
· Screwdriver
· Assistant
· Ratchet Collection
· Warnings
Your primary service panel needs to be clearly marked to indicate that the hot water tank circuit breaker. When it isn't, consult with a professional electrician to ascertain the circuitry of your electric wiring.
If you disconnect the gas supply line in the water tank, then a small number of residual gas will ooze in the pipe. Don't ignite any fires when functioning on gasoline lines.